How much does the lumber for a 6×8 shed cost?

About $629 in framing lumber and sheet goods at national big-box prices (basis 2026-06-05). That covers 278.18 board-feet of framing plus sheathing — not roofing, doors, windows, or finishes.

What size floor joists does it need?

2x6 joists at 16" on-center span the 6-ft width — 7 of them. The size is set by the AWC/IRC span table, not estimated.

What about the roof framing?

14 2x4 common rafters, each 3.7 ft long at a 4/12 pitch. Length from √(run²+rise²); size from the AWC rafter span table.

6×8 Shed Materials List, Cut List & Cost

By the CutlistHQ Editorial Team

$629

Estimated framing cost · 278.18 board-feet

⚠️ Safety Notice: This calculation produced 1 safety-relevant warning. Review the Important Considerations section below before proceeding.

Recalculate

$629est. framing materials

278.18 board-feet · basis 2026-06-05

Framing members

Qty	Size	Length	Part
7	2x6	6.0 ft	Floor joist ⓘ
2	2x6	8.0 ft	Rim joist ⓘ
24	2x4	7.6 ft	Wall stud ⓘ
7	2x4	12.0 ft	Wall plate ⓘ
14	2x4	3.7 ft	Common rafter ⓘ
1	2x6	8.0 ft	Ridge board ⓘ

Sheet goods (10% waste included)

Sheets	Material	Area
2	Floor decking (3/4")	48 ft²
8	Wall sheathing (7/16")	224 ft²
3	Roof sheathing (7/16")	65.92 ft²

Optimized buy list (minimizes offcut waste)

10× 2x6 at 8 ft
7× 2x4 at 12 ft
31× 2x4 at 8 ft

Also needed for this build (not in the framing cost)

A pre-hung or built-up door (single or double) sized to your largest item.
Roofing (shingles or metal), drip edge, and underlayment — sold by the roof square.
Pressure-treated skids or a gravel/concrete pad for the foundation.

How This Was Calculated

Computed from documented residential framing standards for 6×8 shed: span-table member sizing, on-center counts, roof geometry, and a national-midpoint cost basis (2026-06-05).

L = √(run² + rise²) + overhang, rise = run × (pitch ÷ 12)

run: half the span: 3 ft
pitch: roof rise per 12 of run: 4/12
overhang: rafter tail: 6 in

Important Considerations

⚠️Check local codes before you build

These quantities are computed from published residential framing standards for a non-habitable accessory structure. They are an estimate, not a permit-stamped engineered plan. Many jurisdictions exempt small accessory structures under 120–200 sq ft, but snow load, wind zone, and foundation requirements vary — confirm with your local building department, and have any structure carrying unusual load reviewed by a licensed engineer.

Source: IRC accessory-structure provisions; local building department

📐 How these numbers are computed

Member sizes come from documented span tables (AWC/IRC, 16" O.C., No.2 SPF); member counts from on-center spacing; rafter lengths from roof geometry √(run²+rise²); board-feet by the nominal (T×W×L)/144 rule; lumber actual dimensions per US DOC PS 20. Cost is a national big-box midpoint estimate, basis 2026-06-05, and varies by region.

Source: AWC Span Calculator · IRC R602/R802 · US DOC PS 20

Material-estimate gotchas

Buy 10% extra sheet goods for cutting waste — already included in the sheet counts.
These figures are framing only: roofing, siding, doors, windows, paint, and structure-specific items are separate.
Pressure-treated stock is required for the bottom plate and any wood near grade — specify PT at purchase.
Confirm joist and rafter sizes against your local snow/wind load; the tool uses a conservative light-load span table.

Frequently Asked Questions

How much does the lumber for a 6×8 shed cost?: About $629 in framing lumber and sheet goods at national big-box prices (basis 2026-06-05). That covers 278.18 board-feet of framing plus sheathing — not roofing, doors, windows, or finishes.
What size floor joists does it need?: 2x6 joists at 16" on-center span the 6-ft width — 7 of them. The size is set by the AWC/IRC span table, not estimated.
What about the roof framing?: 14 2x4 common rafters, each 3.7 ft long at a 4/12 pitch. Length from √(run²+rise²); size from the AWC rafter span table.

This is the materials math for 6×8 shed. To cut and assemble it you need the dimensioned plan set — panel layouts, joinery, door and roof details. See the plan options below.

Get the dimensioned plans

You can find free plans online, but they usually skip the exact cut list — and a single wrong cut wastes $100–200 in lumber. A complete dimensioned plan set with a real cut list (matching the materials computed above) is a few dollars and saves the weekend.

Plan setMyShedPlans (12,000+ plans)A large dimensioned shed-plan library with cut lists, materials lists, and step-by-step drawings.See details →Indie PDFIndie plan PDF (Etsy)A clean single-structure plan PDF from an independent designer — often the simplest, lowest-risk option.See details →MaterialsShop this materials listOrder the computed lumber and sheet goods from a home center and have them ready for your build.See details →

We may earn a commission from plan purchases, at no extra cost to you. Our materials math is computed from published standards and is never affected by who pays us. Full disclosure.